Building Safety Flame Retardant Net

Product Introduction Of The Building Safety Flame Retardant Net 

The Building safety flame retardant net mainly includes: breaking strength, elongation at break, joint tensile strength, tear strength, penetration resistance, breaking strength retention after aging, and strong tail flame retardant performance. Both flat and vertical nets should be impact resistant. The vertical net cannot replace the flat net, and the flat net or the vertical net should be separated according to the construction needs and the load height. The load strength of the flat net is greater than that of the vertical net. The materials used are more and the weight is greater than the vertical net. Under normal circumstances, the flat net is greater than 5.5kg, and the vertical net is greater than 2.5kg. 
 

Product Parameter Of The Building Safety Flame Retardant Net

Product Use Precautions Of The Building Safety Flame Retardant Net 
Precautions for use of the Building safety flame retardant net：

1.When using, avoid the following phenomena: (1) casually remove the components of the safety net; (2) jump into or put the items into the safety net; (3) massively weld Mars or other Mars into the safety net; (4) in safety Stacking items inside or below the net; (5) Severe corrosive fumes around the safety net.

2. For the safety net in use, regular or irregular inspections should be carried out, and the contamination of debris falling in the net should be cleaned in time. When it is subjected to a large impact, it should be replaced in time. 
 

FAQ: 
1, manufacturers supply genuine
Factory direct sales, short production cycle, price concessions, quality assurance
2, on the manual measurement of size, there is error
3, about color
Camera shooting a little error
4, about customer service
If you have any questions, please contact customer service. If you want to make a reservation, please contact customer service.
5, about after sales
If you have any problems after receiving the goods, please report the problem within 15 days.
6, on the delivery and shipping costs
Because this product is heavy goods, the logistics will not be collected when the purchase amount is small, and the delivery price is too high, so we suggest to buy one product and send logistics to save your cost. 

Tips: 
Standard for the use of building safety nets:
1. The safety net must be hung under the working part of the high place; when the height of the building exceeds 4m, a safety net that gradually rises with the wall must be set, and then a fixed safety net is set every 4m; in the outer frame and the bridge frame A safety net must be installed at the upper and lower holes. The erection of the safety net should be low and high, and the height difference of the expenditure part is generally about 5Ocm; the support rod is not broken or bent; the gap between the inner edge of the net and the wall is less than 15cm; the distance between the lowest point of the net and the surface of the lower surface is greater than 3m. . For the support used for the safety net erection, the diameter of the small head of the wooden pole shall not be less than 7cm, the diameter of the small head of the bamboo pole shall not be less than 8cm, and the spacing of the poles shall not be greater than 4m.
2. Check the safety net for corrosion and damage before use. During the construction, it is necessary to ensure that the safety net is complete and effective, the support is reasonable, the force is even, and there is no debris in the net. The lap joints shall be tight and secure, and there shall be no gaps. The safety nets to be erected shall not be demolished or damaged during the construction period, and must be removed only when there is no height. When the construction needs to temporarily remove the safety net that has been erected, the construction unit must notify and ask the erection unit for approval before dismantling. The construction must be completed immediately after the construction unit is restored according to the requirements, and can only be used after passing the inspection by the erection unit.
3. Always clean the debris in the net. When performing welding operations on the top of the net, take effective measures to prevent the welding spark from falling on the net; do not have long-term serious acid-base smoke around the net.
4. The safety net must be inspected frequently during use and has tracking usage records. Safety nets that do not meet the requirements should be processed in a timely manner. When the safety net is not in use, it must be properly stored and kept to prevent moisture and mildew. The new network must check the nameplate of the product before use: firstly, whether it is flat or vertical, the net and the net must be strictly separated, and the net must not be used as a flat net; when the net is set up, the bottom tether must be The tie is firm. Production license of the manufacturer; the factory certificate of the product, if the old network should be tested before use, and there is a test report, the old network that passed the test can be used.